What have you done to your car today?

[Sgr74]

New stuff arrives tomorrow new suplex rear springs and seat belt guides for my m3 E46 seats FF857ABC-BDF0-47E6-B451-4F82B27EF0C0.png08DD1522-086C-4F31-B482-F39B92845D46.jpeg

Do the seatbelt supports work?
I kind of want to push the belt away from my neck. I looked at these and dismissed them because the belt would still chafe on the neck.

[Coffee331]

Fitted new drop links and anti roll bar bushes

[bz4kev]

New stuff arrives tomorrow new suplex rear springs and seat belt guides for my m3 E46 seats FF857ABC-BDF0-47E6-B451-4F82B27EF0C0.png08DD1522-086C-4F31-B482-F39B92845D46.jpeg

Do the seatbelt supports work?
I kind of want to push the belt away from my neck. I looked at these and dismissed them because the belt would still chafe on the neck.

to a degree helps keep belt from falling behind the seat but the belt can slip out a bit to easy when putting belt on only just fitted them so will let you know with regards to chaffing

[DavesZed]

Snapped the brake bleed nipped in front drivers side caliper, last one to bleed ,totally pizzzd off,caliper off and hopefully drilled and tapped Monday fingers crossed.

[DaveZ4richardson]

Had a spin around the Lakes today, no roof down though sadly, was a happy chap when a lady in the car park in Ambleside came across and asked what polish I used, she was very impressed with the shine and finish on the paintwork, makes all the hardwork worthwhile

[rally-chris]

Private plates on, roof wrapped gloss black and missing headlamp washer cover painted (but not yet fitted).

39A78E00-0CDD-429B-902A-C0DBD4A3A498.jpeg (561.64 KiB) Viewed 691 times

On the downside, my engine check light has come back on again (lambda sensor fault) and I’ve got an exhaust related rattle just above idle - both a legacy of the recent Scorpion exhaust install!

Chris

[Ducklakeview]

Checked the rear discs for run out as could feel a little vibration on braking, they run out by 0.05mm or about. 002" which I presume is acceptable?

20171106_170058.jpg (195.23 KiB) Viewed 674 times

Mike

[G600]

Checked the rear discs for run out as could feel a little vibration on braking, they run out by 0.05mm or about. 002" which I presume is acceptable?

20171106_170058.jpg

Mike

That's fine especially measured that close to the edge.

[Ducklakeview]

Checked the rear discs for run out as could feel a little vibration on braking, they run out by 0.05mm or about. 002" which I presume is acceptable?

20171106_170058.jpg

Mike

That's fine especially measured that close to the edge.

Fronts were even less, 0.02mm so the vibration is coming from elsewhere...

Mike

[G600]

Fronts were even less, 0.02mm so the vibration is coming from elsewhere...

Mike

Have you checked for variation in the disc thickness? The limit for that is only .01mm (E30 but I can't see it being different on an E85)

[MACK]

Checked the rear discs for run out as could feel a little vibration on braking, they run out by 0.05mm or about. 002" which I presume is acceptable?

20171106_170058.jpg

Mike

That's fine especially measured that close to the edge.

Fronts were even less, 0.02mm so the vibration is coming from elsewhere...

Mike

Have you checked your front rtab's?

[Ducklakeview]

That's fine especially measured that close to the edge.

Fronts were even less, 0.02mm so the vibration is coming from elsewhere...

Mike

Have you checked your front rtab's?

Replaced 3 months ago. It's only a very slight vibration, but doing my head in.

Mike

[bz4kev]

New stuff arrives tomorrow new suplex rear springs and seat belt guides for my m3 E46 seats FF857ABC-BDF0-47E6-B451-4F82B27EF0C0.png08DD1522-086C-4F31-B482-F39B92845D46.jpeg

Do the seatbelt supports work?
I kind of want to push the belt away from my neck. I looked at these and dismissed them because the belt would still chafe on the neck.

hi mate I would say not much different maybe a little more clearance but to be honest I only got them to stop the belt disappearing behind the seat and having to search for it behind me also think I will have to mod it some way to stop the belt slipping out of the clip but certainly better than it was

[MACK]

That's fine especially measured that close to the edge.

Fronts were even less, 0.02mm so the vibration is coming from elsewhere...

Mike

Have you checked your front rtab's?

I guess it's a process of elimination then and checking the usual suspension components/ball joints etc. I'd probably start with the ball joints on the front arms

[Paulr]

Fronts were even less, 0.02mm so the vibration is coming from elsewhere...

Mike

Have you checked your front rtab's?

I guess it's a process of elimination then and checking the usual suspension components/ball joints etc. I'd probably start with the ball joints on the front arms

Is it me, or does that disc look really worn? Should the lip be that deep?