Not joined yet? Register for free and enjoy features such as alerts, private messaging and viewing latest posts and topics.

My Z4 28i

Specific discussion about the E89 2009 Z4 (sDrive35is, sDrive35i, sDrive30i, sDrive23i)
Post Reply
User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Thu Oct 12, 2017 8:47 am

PinkPineapple44 wrote: Wed Oct 11, 2017 8:32 pm
SteveSmith wrote: Wed Oct 11, 2017 6:59 pm
PinkPineapple44 wrote: Wed Oct 11, 2017 2:37 pm

The front height of the E89 has always bugged me, the arch gap is just so big! I was looking at buying the Eibach pro kit soon over the H&R, but as you say it still doesn't lower the front as much as we would like.

Would you still opt for the Eibach kit again if you had another go at it?
I would.

Personally, I think the 4 pot doesn't weigh enough so Eibachs plus 6 cylinder looks good.

The H&R's sit too low at the rear for me.
Ideally the front arch gap would reduce by 50%, but the rear is almost perfect as it is for me.

orca-image-1507482021431.jpg_1507482021623.jpeg

Where did you see these thicker spring pads?
When I got the Eibachs I was tempted to just fit the fronts as you say, the rear looks fine as is imo. I didn't do this as I wasn't sure how that would effect the handling (stiffer on the front than the rear is likely to encourage understeer (I believe!) and no one wants that!).

I found the thicker pad on eBay. That should raise the rear slightly, basically back to stock height and give the stance needed.

I really should have gone for coilovers as I'm stupidly fussy about the rake of a car but I have adaptive shocks and I like them!
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

User avatar
sunnydays
Member
Member
Posts: 983
Joined: Fri Sep 23, 2016 7:50 am

My Z4 28i

Post by sunnydays » Thu Oct 12, 2017 12:10 pm

SteveSmith wrote: Thu Oct 12, 2017 8:47 am
PinkPineapple44 wrote: Wed Oct 11, 2017 8:32 pm
SteveSmith wrote: Wed Oct 11, 2017 6:59 pm

I would.

Personally, I think the 4 pot doesn't weigh enough so Eibachs plus 6 cylinder looks good.

The H&R's sit too low at the rear for me.
Ideally the front arch gap would reduce by 50%, but the rear is almost perfect as it is for me.

orca-image-1507482021431.jpg_1507482021623.jpeg

Where did you see these thicker spring pads?
When I got the Eibachs I was tempted to just fit the fronts as you say, the rear looks fine as is imo. I didn't do this as I wasn't sure how that would effect the handling (stiffer on the front than the rear is likely to encourage understeer (I believe!) and no one wants that!).

I found the thicker pad on eBay. That should raise the rear slightly, basically back to stock height and give the stance needed.

I really should have gone for coilovers as I'm stupidly fussy about the rake of a car but I have adaptive shocks and I like them!
The eibachs only drop the front if you have m sport suspension already.

The drop is 10mm up front and 0mm rear.

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Thu Oct 12, 2017 5:15 pm

sunnydays wrote: Thu Oct 12, 2017 12:10 pm
SteveSmith wrote: Thu Oct 12, 2017 8:47 am
PinkPineapple44 wrote: Wed Oct 11, 2017 8:32 pm

Ideally the front arch gap would reduce by 50%, but the rear is almost perfect as it is for me.

orca-image-1507482021431.jpg_1507482021623.jpeg

Where did you see these thicker spring pads?
When I got the Eibachs I was tempted to just fit the fronts as you say, the rear looks fine as is imo. I didn't do this as I wasn't sure how that would effect the handling (stiffer on the front than the rear is likely to encourage understeer (I believe!) and no one wants that!).

I found the thicker pad on eBay. That should raise the rear slightly, basically back to stock height and give the stance needed.

I really should have gone for coilovers as I'm stupidly fussy about the rake of a car but I have adaptive shocks and I like them!
The eibachs only drop the front if you have m sport suspension already.

The drop is 10mm up front and 0mm rear.
There are different kits. Mine should have lowered the front 15mm and the rear 5mm. Which is probably about right in terms of what it's actually done.

It's definitely lowered the rear over standard as I've parked next to standard E89 M Sports.
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

Online
User avatar
mr wilks
Legend
Legend
Posts: 21894
Joined: Wed Jul 04, 2012 10:02 pm
Location: Lancashire

My Z4 28i

Post by mr wilks » Thu Oct 12, 2017 5:52 pm

Have you a link to the thicker pads Steve ?
3 ZMRs
3 E89s
5 Si coupes
5 Si roadsters
997 C4
TTRS
F82 M4
MK7 Golf Gti
current Bmw 6 Gran Turismo

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Thu Oct 12, 2017 8:03 pm

mr wilks wrote: Thu Oct 12, 2017 5:52 pm Have you a link to the thicker pads Steve ?

https://www.ebay.co.uk/i/162631111668

I'm just awaiting delivery. Do you think the H&R's sit too low at the rear as well? I'll let you know if these work.
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

Online
User avatar
mr wilks
Legend
Legend
Posts: 21894
Joined: Wed Jul 04, 2012 10:02 pm
Location: Lancashire

My Z4 28i

Post by mr wilks » Fri Oct 13, 2017 8:19 am

SteveSmith wrote: Thu Oct 12, 2017 8:03 pm
mr wilks wrote: Thu Oct 12, 2017 5:52 pm Have you a link to the thicker pads Steve ?

https://www.ebay.co.uk/i/162631111668

I'm just awaiting delivery. Do you think the H&R's sit too low at the rear as well? I'll let you know if these work.
Tbh id like the back up 10mm just for the added gap between tyre & liner . As you will know the way the liner protrudes on the rear is annoying .
Even after a few short drives i wouldn't want rid of the H & Rs as to my mind they have enhanced the ride but a nudge up at the rear would give me perfection all round
3 ZMRs
3 E89s
5 Si coupes
5 Si roadsters
997 C4
TTRS
F82 M4
MK7 Golf Gti
current Bmw 6 Gran Turismo

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Fri Oct 13, 2017 8:52 am

mr wilks wrote: Fri Oct 13, 2017 8:19 am
SteveSmith wrote: Thu Oct 12, 2017 8:03 pm
mr wilks wrote: Thu Oct 12, 2017 5:52 pm Have you a link to the thicker pads Steve ?

https://www.ebay.co.uk/i/162631111668

I'm just awaiting delivery. Do you think the H&R's sit too low at the rear as well? I'll let you know if these work.
Tbh id like the back up 10mm just for the added gap between tyre & liner . As you will know the way the liner protrudes on the rear is annoying .
Even after a few short drives i wouldn't want rid of the H & Rs as to my mind they have enhanced the ride but a nudge up at the rear would give me perfection all round
It's a pain in the arse yes. But Eibachs, 20mm spacers and no liner still rubbed like mad!
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Wed Nov 22, 2017 7:30 pm

Thought I’d update my progress thread with a pic of the new wheels!

[IMG]http://i129.photobucket.com/albums/p206 ... 42615F.jpg[/IMG]
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

User avatar
Kugaman1
Member
Member
Posts: 367
Joined: Sun Jul 30, 2017 6:16 pm
Location: North East Scotland

My Z4 28i

Post by Kugaman1 » Thu Nov 23, 2017 12:41 am

Hmm.
Each to their own I suppose. I’m surprised you went with something so bling after toning down the side repeaters and front grille?
To be honest I think you had the look of the car absolutely nailed here.....
60E58D95-6381-4A29-911A-E90415684967.jpeg
60E58D95-6381-4A29-911A-E90415684967.jpeg (255.09 KiB) Viewed 986 times
Now it’s looking too aftermarket for my tastes.....

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Thu Nov 23, 2017 1:10 pm

Kugaman1 wrote: Thu Nov 23, 2017 12:41 am Hmm.
Each to their own I suppose. I’m surprised you went with something so bling after toning down the side repeaters and front grille?
To be honest I think you had the look of the car absolutely nailed here.....
60E58D95-6381-4A29-911A-E90415684967.jpeg

Now it’s looking too aftermarket for my tastes.....
So do I! I loved the 326’s but it failed the MOT due to a cracked wheel.

The 359’s are the only other BMW wheel I wanted on the car so thought I’d try them. I’m not totally convinced.

The colour “hyper silver” is a tad bling for my liking but I didn’t want black wheels.

I do think the lighting (plus me messing around with settings) have made the wheels look even More bling than they are in the flesh!

I may look at toning them down slightly with a darker silver / light anthracite colour later.

I may go back to 326’s!? Who knows.

I’m enjoying it at the moment though!
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

mcbutler
Senior Member
Senior Member
Posts: 2551
Joined: Fri May 26, 2017 3:40 pm
Location: Plymouth

My Z4 28i

Post by mcbutler » Thu Nov 23, 2017 4:42 pm

ruffedlemurz4 wrote: Tue Nov 22, 2016 7:14 pm I'm pro wind deflectors! I don't have the later chrome repeaters but I have seen pictures on threads on here where people have painted them black to go with black grilles.
You could always swap them for the older simpler ones as the repeaters sell for about or over£100 on eBay. Viv
I have a set of older ones you can have for nothing if you want them?
Mark
Plymouth
E89
35i
Carmine Red
Black leather

User avatar
Kugaman1
Member
Member
Posts: 367
Joined: Sun Jul 30, 2017 6:16 pm
Location: North East Scotland

My Z4 28i

Post by Kugaman1 » Thu Nov 23, 2017 7:12 pm

Well, glad your enjoying it, its all in the eye of the beholder as they say!

Im certainly going to look at wrapping the bottom edge of the front bumper on mine. It looks excellent on yours.

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Thu Nov 23, 2017 8:40 pm

Kugaman1 wrote: Thu Nov 23, 2017 7:12 pm Well, glad your enjoying it, its all in the eye of the beholder as they say!

Im certainly going to look at wrapping the bottom edge of the front bumper on mine. It looks excellent on yours.
Yes, the bottom bar wrapped makes a huge difference! It visually lowers and deepens the front bumper.

I keep looking at the picture now atvthe Shell garage and I really did love the look of it then!
28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

User avatar
Kugaman1
Member
Member
Posts: 367
Joined: Sun Jul 30, 2017 6:16 pm
Location: North East Scotland

My Z4 28i

Post by Kugaman1 » Fri Nov 24, 2017 1:47 am

Agreed mate, that picture nails the look of the car.
Really looks just perfect.

User avatar
SteveSmith
Member
Member
Posts: 760
Joined: Wed Nov 16, 2016 11:33 am

My Z4 28i

Post by SteveSmith » Sat Nov 25, 2017 2:52 pm

28i M Sport - Alpine White / Canberra Beige, 19" M359’s, H&R’s / Eibachs, BMS Stage 1 - 271bhp, Front Splitter, CF Rear Lip, Alcantara Steering Wheel and Brembo 4 pots

Image

Post Reply